Use Sea Clone Skimmer question

new2salt2 · 09-12-2003, 05:27 AM

hi, am new to the salt thing and purchased a used Skimmer from a person in another city. Well its a backpack style sea clone and uses a power head. I guess there is suposed to be a hose with a air valve connecting to a sponge then that attached to a cone shaped item, which then attached to the intake of the power head . There is then a tube running to the bottom of the skimmer and overflows into the tank.

my question is i dont have the air tube, sponge, or cone just the power head and hose that runs to the skimmer. Will it still work? or do i need to have the air hose and such?

blown63chevy · 09-12-2003, 11:20 AM

Hi and welcome to the hobby.
I am currently running the same type of skimmer on my 45g hex. It's not the best, but will work for now until you can upgrade to a better one. To use the skimmer as designed, you will need the missing parts. The air line tubing is how the air gets into the water coloum thru a ventura to make the skimmer work. As I stated, it's not the most efficent, but it works. The biggest problem with the design is that it dosent actually skim the water from the surface, but below the surface.
I have modified mine by removing the air line and cutting the water tubing to install flexable line so that I could place the inlet side of the pump at the waters surface. It will then skim at the surface as well as ingest air at the same time. However it does make some noise, but it works for now until I can get my new tank set up. Hope this helps some.
Ray

new2salt2 · 09-13-2003, 06:19 AM

ok .. so does anyone have any idea where i can get the missing parts at? would it be possible to buy another powerhead and if so what kind would fit up to the skimmer lines and work properly?

saltwaterdave · 09-13-2003, 11:31 PM

http://reefcentral.com/diy/seaclone_modifications.htm

Try this it worked for me.I use it on a 30 gallon tank,I would try it on anything bigger though but it does work pretty good for this tank.
David

new2salt2 · 09-14-2003, 05:27 AM

well thing is i am going to have to replace the entire maxijet becasue i dont have the sponge or the vortex piece for it.

think i should buy the same type , or go witha more powerful one?

saltwaterdave · 09-15-2003, 08:57 PM

Quote:

Originally Posted by new2salt2

well thing is i am going to have to replace the entire maxijet becasue i dont have the sponge or the vortex piece for it.

think i should buy the same type , or go witha more powerful one?

I would use the same pump.

09-12-2003, 05:27 AM	#1
new2salt2 Citizen Join Date: Apr 2003 Location: wasington Posts: 163	Use Sea Clone Skimmer question hi, am new to the salt thing and purchased a used Skimmer from a person in another city. Well its a backpack style sea clone and uses a power head. I guess there is suposed to be a hose with a air valve connecting to a sponge then that attached to a cone shaped item, which then attached to the intake of the power head . There is then a tube running to the bottom of the skimmer and overflows into the tank. my question is i dont have the air tube, sponge, or cone just the power head and hose that runs to the skimmer. Will it still work? or do i need to have the air hose and such?

09-13-2003, 06:19 AM	#3
new2salt2 Citizen Join Date: Apr 2003 Location: wasington Posts: 163	so where can i gt the parts ok .. so does anyone have any idea where i can get the missing parts at? would it be possible to buy another powerhead and if so what kind would fit up to the skimmer lines and work properly?

09-14-2003, 05:27 AM	#5
new2salt2 Citizen Join Date: Apr 2003 Location: wasington Posts: 163	thanks well thing is i am going to have to replace the entire maxijet becasue i dont have the sponge or the vortex piece for it. think i should buy the same type , or go witha more powerful one?

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
AquaC EV Skimmer Question	SupaJSK	Tanks, Filtration & Basic Equipment	0	10-28-2002 12:14 PM
skimmer question	jsaltzgi	Tanks, Filtration & Basic Equipment	4	02-15-2002 09:07 AM
FS in Chicago - Tetra Luft Pump, Berlin Air Lift 60 Skimmer, Red Sea airstones	botp2k1	For Sale or Trade Zone	0	11-15-2001 07:33 AM
etss skimmer problems	golfcole	Tanks, Filtration & Basic Equipment	2	07-22-2001 11:01 PM
Skimmer and refugium Question (long)	Marcel	Reef Aquariums	3	06-18-2001 01:08 PM

09-12-2003, 11:20 AM	#2
blown63chevy Just Moved In Join Date: Jul 2003 Location: Oxnard, Calif. Posts: 34	Hi and welcome to the hobby. I am currently running the same type of skimmer on my 45g hex. It's not the best, but will work for now until you can upgrade to a better one. To use the skimmer as designed, you will need the missing parts. The air line tubing is how the air gets into the water coloum thru a ventura to make the skimmer work. As I stated, it's not the most efficent, but it works. The biggest problem with the design is that it dosent actually skim the water from the surface, but below the surface. I have modified mine by removing the air line and cutting the water tubing to install flexable line so that I could place the inlet side of the pump at the waters surface. It will then skim at the surface as well as ingest air at the same time. However it does make some noise, but it works for now until I can get my new tank set up. Hope this helps some. Ray

09-13-2003, 11:31 PM	#4
saltwaterdave Citizen Join Date: Aug 2002 Location: Virginia Posts: 145	http://reefcentral.com/diy/seaclone_modifications.htm Try this it worked for me.I use it on a 30 gallon tank,I would try it on anything bigger though but it does work pretty good for this tank. David

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)