Powerhead Heat Generation

NoSump · 12-13-2004, 04:03 PM

As I am still in the curing of new live rock stage, I am not currently using any lighting in my tank. I will be running four 96 watt pc's and do have concerns regarding heat generation when the lighting is activated (I would prefer not to have to go the chiller route).

That being said, I appear to have a temperature challenge prior to activation of lighting. All that is currently running is the filtration system and two Maxi-Jet 900 powerheads. For some reason, even though my heaters are turned way down to 74 degrees, my tank temperture is currently 80 (and the room temperature is 73).

My question is, would the two submerged powerheads generate sufficient heat to drive up my tank temperature? My guess is that the submerget powerheads should not generate that much heat - but I look forward to input.

**Poseidon** · 12-13-2004, 04:59 PM

I would suspect NO what size is your tank? Also check to make sure that nothing is jammed in the impellar of either powerhead. I have 2 MAG 12's and 2 Hagen 402's and I don't get anywhere near the kind of heat you are describing.

NoSump · 12-13-2004, 08:07 PM

It's on;y 72 gallons. Thanks, I didn't think that the powerheads should generate that much heat. I am trying to eliminate suspects. I'm going to try to disconnect one heater at a time in order to see if there is some problem with one of the thermostats.

**Poseidon** · 12-13-2004, 09:10 PM

No problems... I would suspect a heater myself.

12-13-2004, 04:03 PM	#1
NoSump Citizen Join Date: Nov 2004 Location: USA Posts: 215	Powerhead Heat Generation As I am still in the curing of new live rock stage, I am not currently using any lighting in my tank. I will be running four 96 watt pc's and do have concerns regarding heat generation when the lighting is activated (I would prefer not to have to go the chiller route). That being said, I appear to have a temperature challenge prior to activation of lighting. All that is currently running is the filtration system and two Maxi-Jet 900 powerheads. For some reason, even though my heaters are turned way down to 74 degrees, my tank temperture is currently 80 (and the room temperature is 73). My question is, would the two submerged powerheads generate sufficient heat to drive up my tank temperature? My guess is that the submerget powerheads should not generate that much heat - but I look forward to input.

12-13-2004, 04:59 PM	#2
Poseidon Moderator Join Date: Sep 2001 Location: Swartz Creek, MI Posts: 6,166	I would suspect NO what size is your tank? Also check to make sure that nothing is jammed in the impellar of either powerhead. I have 2 MAG 12's and 2 Hagen 402's and I don't get anywhere near the kind of heat you are describing. __________________ Need a Photographer? Just say NO to CRABS Mike

12-13-2004, 09:10 PM	#4
Poseidon Moderator Join Date: Sep 2001 Location: Swartz Creek, MI Posts: 6,166	No problems... I would suspect a heater myself. __________________ Need a Photographer? Just say NO to CRABS Mike

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
New Penguin Powerhead	cesar	Tanks, Filtration & Basic Equipment	0	09-18-2004 05:44 PM
PowerHead Question?	Tattooedlife	Reef Aquariums	3	01-04-2004 11:53 AM
eggcrate; how heat resistant?	jwtrojan44	Lighting	7	08-12-2001 11:44 PM
3rd Generation Colt Polyps (Photo)	Reinhold	Reef Aquariums	4	07-22-2001 07:31 PM
Question for Spasse, and others (EE)	Ltspd	Equipment Archives	10	03-05-2001 12:15 AM

12-13-2004, 08:07 PM	#3
NoSump Citizen Join Date: Nov 2004 Location: USA Posts: 215	It's on;y 72 gallons. Thanks, I didn't think that the powerheads should generate that much heat. I am trying to eliminate suspects. I'm going to try to disconnect one heater at a time in order to see if there is some problem with one of the thermostats.

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)